TL;DR: Combustible dust is fine dust from materials that burn, such as flour, sugar, timber, plastics and aluminium. When it’s spread through the air and ignited in an enclosed space, it can explode. The biggest danger sits overhead: a small blast can shake dust loose from rafters, beams and racking, and that dust fuels a far larger second explosion. A layer as thin as about 0.8 mm across a wide area is considered hazardous, so high-level surfaces need regular, vacuum-based cleaning.
Combustible dust becomes a fire and explosion risk once it builds up on surfaces where it can be disturbed into the air. In factories, that build-up usually happens out of sight: on roof trusses, beams, light fittings, ducts and the tops of racking. High-level cleaning removes that hidden fuel before an ignition source finds it. For manufacturers across Melbourne’s south-east, from Dandenong South to Braeside, it’s one of the most overlooked parts of site safety.
What is combustible dust?
Combustible dust is fine particles of any material that burns. When those particles are suspended in air, they can catch fire or explode. A solid block of timber is hard to light. The same timber as fine sawdust, floating in a cloud, can ignite in a fraction of a second.
A dust explosion needs five things at once, often called the dust explosion pentagon:
- fuel (the combustible dust)
- oxygen in the air
- an ignition source, such as a spark, hot surface or flame
- dispersion, where the dust is lifted into a cloud
- confinement, such as a room, silo or piece of equipment
Remove any one of the five and an explosion can’t happen. Housekeeping targets two of them: it removes the fuel and stops the dust being dispersed.
Common combustible dusts in Melbourne industry
Many of the products made in Melbourne’s industrial suburbs create combustible dust:
| Industry | Typical combustible dust |
| Bakeries and food manufacturing | Flour, sugar, starch, milk powder, spices |
| Timber, joinery and cabinet making | Sawdust and fine MDF dust |
| Plastics and powder coating | Resin powders and plastic fines |
| Metal fabrication and finishing | Aluminium and magnesium dust from grinding and polishing |
| Packaging, paper and printing | Paper and cardboard dust |
| Pharmaceuticals and chemicals | Fine powdered ingredients |
If your site handles any of these as a fine powder, treat the dust as combustible until testing shows otherwise.
Why is dust on rafters and beams the real danger?
Overhead dust is dangerous because it feeds the secondary explosion, which usually does the most damage. A small primary explosion or flash fire inside a machine, dust collector or duct creates a pressure wave. That wave shakes years of settled dust off rafters, beams and ledges, forming a much larger cloud, and the fire front ignites it.
Australia has its own documented warning. In a 2016 safety alert, WorkSafe WA described a farmer who tried to put out a barley grain fire inside a large silo by spraying water through the roof hatch. The water let in more air and may have raised more grain dust, and the suspended grain dust ignited, causing an explosion that blew the roof off. The farmer fell to the ground and was seriously injured.
The same thing can happen inside a factory: a fire becomes an explosion once dust is lifted into the air. Guidance from the Australian Forest Products Association, the timber industry body, warns that sawdust on structural elements such as beams can result in explosions. It calls housekeeping of elevated and hidden surfaces essential.
The same principle applies to a Dandenong bakery or a Braeside joinery shop. The dust on the floor is visible and gets swept daily. The dust on top of a 9-metre beam often hasn’t been touched in years.
How much dust build-up is too much?
US fire safety guidance from the National Fire Protection Association (NFPA) treats a dust layer as thin as 1/32 of an inch, about 0.8 mm, as a hazardous build-up when it covers a large area. That’s roughly the thickness of a paperclip wire.
Here’s a simple check for high-level surfaces:
- From a safe platform, run a finger or a ruler edge across a beam or the top of a light fitting.
- If you can’t see the colour of the surface underneath, the layer is probably at or above 0.8 mm.
- Check several spots, including surfaces directly above dusty processes such as mixers, saws and grinders.
Australia doesn’t have a single national rule that sets a maximum dust depth. Sites with combustible dust should classify their hazardous areas under AS/NZS 60079.10.2 and set their own cleaning triggers. The 0.8 mm figure is a practical benchmark many safety managers use. For the wider signs that a site needs more than routine cleaning, see our post on the 5 signs your factory needs a deep clean.
How is high-level cleaning done?
High-level cleaning is done from the top down, with vacuums rather than blowing, by trained operators working from a safe platform. The aim is to remove dust from the building without putting it back into the air.
Elevated work platforms and scissor lifts vs extended poles
Extended poles with vacuum heads suit lower surfaces, such as racking and wall ledges. Higher up, operators work from scissor lifts or boom-type elevating work platforms (EWPs) so they can see the surface they’re cleaning.
Vacuum, not blow-down: why compressed air spreads the risk
Compressed air moves dust around a factory without removing it. Blowing dust off a beam creates the exact cloud a dust explosion needs, and the dust lands again on lower surfaces and machinery. Australian industry guidance treats low-pressure compressed air as a last resort only.
Where combustible dust is present, the type of vacuum matters too. A standard workshop vacuum can itself be an ignition source. Sites should use vacuums suited to their hazardous area classification, earthed to control static.
Racking, light fittings, ducts and roof trusses
Each overhead surface collects dust differently:
- Roof trusses and purlins hold the largest total area of settled dust.
- Light fittings and heaters combine dust with heat, so they’re cleaned with the power isolated.
- Ductwork and cable trays collect dust on top and inside, and the tops are often missed.
- Racking tops and pallet stock gather dust from forklift traffic and nearby processes.
Cleaning works down from the roof to the racking and then to the floor, so nothing gets dusted again after it’s been cleaned.
If your Melbourne site has overhead dust you can’t reach safely, SM&MN Cleaning offers high warehouse ceiling dusting as part of its factory cleaning work. Get a free quote or call 1300 142 715.
What safety controls are needed during high-level cleaning?
High-level cleaning needs controls for two risks at once: working at height and disturbing combustible dust. Before work starts, the site and the cleaning team should agree on:
- an exclusion zone under the work area, so falling dust or tools can’t hit anyone below
- no hot work, such as welding or grinding, in the area while cleaning is under way
- isolating or protecting heat sources such as heaters and high-bay lights
- the right licence for the platform: in Australia, a high risk work licence is needed to operate a boom-type EWP with a boom of 11 metres or more, and scissor lift operators must be trained to use them safely
- P2 respirators and eye protection, since disturbed dust is also an inhalation hazard
- a check of the site’s hazardous area zones before any electrical equipment, including vacuums, goes into them
How often should high-level areas be cleaned?
High-level areas should be cleaned before the dust layer reaches a hazardous depth, so the right frequency depends on how fast your process creates dust. As a general guide:
| Site type | Inspect overhead surfaces | Typical high-level clean |
| Storage warehouse, low dust | Quarterly | Every 6–12 months |
| Light manufacturing | Monthly | Every 3–6 months |
| Flour, sugar, timber, powder coating or metal finishing | Monthly or more | Every 1–3 months, or when the 0.8 mm check fails |
Your site’s own risk assessment and dust management plan should set the final schedule. If the layer check fails between scheduled cleans, bring the clean forward.
How does the SM&MN top-down, vacuum-first approach work?
SM&MN Cleaning has cleaned factories and warehouses across Melbourne’s south-east for 11 years, and it works to one rule with overhead dust. The dust has to leave the building in a vacuum, so none of it settles back onto machines and stock.
The SM&MN top-down, vacuum-first approach has four stages:
- Inspect. Walk the site with the facility manager, check the layer depth at height, and confirm hazardous areas and isolation points.
- Isolate. Set exclusion zones, stop hot work and isolate overhead heat sources.
- Clean top-down. Work from roof trusses to beams, lights, ducts and racking, vacuuming rather than blowing.
- Finish at floor level. Clean the floor last to collect anything that fell during the job.
Working in this order means each surface only needs cleaning once.
Frequently asked questions
Is flour dust combustible?
Yes. Flour, sugar, starch and many other food powders can ignite when they’re dispersed in the air and meet an ignition source in an enclosed space. Bakeries and food factories are common sites with combustible dust. Dust settled on high surfaces above mixers and packing lines is the biggest concern,because a small fire can lift it into a much larger cloud. Our bakery cleaning procedures cover routine bakery cleaning and sanitizing for all bakery equipment.
Why shouldn’t compressed air be used to clean dust?
Compressed air lifts fine dust into the air, which creates the cloud a dust explosion needs. It also moves dust onto lower surfaces and machinery instead of removing it, and it increases the amount of dust workers breathe in. Vacuuming with equipment suited to the site’s hazardous areas is the safer method. Australian industry guidance treats low-pressure compressed air as a last resort only.
How often should warehouse ceilings be cleaned?
Low-dust storage warehouses are commonly cleaned at high level every 6 to 12 months. Sites that create combustible dust, such as bakeries, joinery shops and powder coaters, often need high-level cleaning every 1 to 3 months. The best trigger is a regular layer check: if the dust on beams is close to 0.8 mm thick, it’s time to clean, whatever the schedule says.
Who can operate a scissor lift for cleaning?
Scissor lift operators don’t need a high risk work licence in Australia, but they must be trained and competent to use the machine safely. A high risk work licence is required for boom-type elevating work platforms with a boom of 11 metres or more. Ask any cleaning contractor which platforms they’ll use, and ask to see their operators’ licences and training records.
Can dust on high surfaces cause an explosion?
Settled dust that’s left alone will usually burn rather than explode. The danger comes when something disturbs it. A small explosion or flash fire inside equipment can shake dust off rafters and beams and create a much bigger cloud, which then ignites. In incidents like the 2008 Imperial Sugar explosion, these secondary explosions caused most of the damage, which is why overhead housekeeping matters so much.
Ready to get your high-level surfaces cleaned?
Combustible dust is most dangerous where nobody looks: on rafters, beams, ducts and racking tops, where a small fire can turn it into a much larger explosion. Check the layer depth, clean from the top down with vacuums instead of compressed air, and set the schedule by how much dust your process makes. The SM&MN top-down, vacuum-first approach covers all of this in one planned visit. The Christmas–New Year shutdown is a good window to book it before production restarts. Get a free quote or call SM&MN Cleaning on 1300 142 715.